纸箱采用印刷不仅能更加美观还能吸引更多的消费者前来购买，纸箱厂印刷也会出现印刷错误现象，比如：当橡胶板厚度不均匀时，由多个小的板（为了节省橡胶板与板芯板技术），应该产生相同的块板，糊版或局部图文印迹不清的质量问题，造成印迹不清晰，板的布局会出现高。那遇到此类问题时我们该如何解决呢？
The printing of cartons can not only make them more beautiful, but also attract more consumers to buy them. Printing errors will also occur in carton factory printing. For example, when the thickness of rubber plates is uneven, multiple small plates (in order to save rubber plate and core plate technology) should produce the same quality problems of block plates, paste plates or unclear local graphic imprints, resulting in unclear imprints, The layout of the board will appear high and low. How can we solve such problems?
1、颜色顺序不当造成的质量缺陷
1. Quality defects caused by improper color sequence
如果印刷版面是全文字排列在同一组，当瓦楞纸板在同一组印刷过程中，组印制板图文着墨不良，干燥缓慢，易被弄脏转移造成的版面由脏。为了防止这种病的产生，有必要在组彩色印刷中安排小面积的布局，并将大面积的版面安排在下面的彩色组印刷中，以避免由于转印造成的脏印刷。
If the printed layout is arranged in the same group, when the corrugated board is printed in the same group, the graphics and texts of the group printed board are poorly inked, dry slowly and easy to be dirty, resulting in the dirty layout caused by transfer. In order to prevent this disease, it is necessary to arrange a small area layout in group color printing, and arrange a large area layout in the following color group printing, so as to avoid dirty printing caused by transfer printing.
2、相关部件造成的机器印质量故障
2. Machine print quality failure caused by related components
当印版辊轴、压花辊轴、传动轴、齿轮和压花与重要部件的磨损、松动、跳动或滑动造成压印过程中辊或压花辊现象，由于压力不稳定，导致打印布局和板接触不正常、糊版或局部原因图文印迹不清晰的问题，纸板印刷表面。通过仔细细致的观察和分析，找出故障的确切位置，采取相应的措施加以处理，对磨损和松动部位进行修补，故障现象。
When the wear, looseness, runout or sliding of plate roller shaft, embossing roller shaft, transmission shaft, gear, embossing and important parts cause the phenomenon of roller or embossing roller in the embossing process, the printing layout and board contact are abnormal due to unstable pressure, and the printing plate is pasted or the picture and text imprint is not clear due to local reasons. Through careful observation and analysis, find out the exact location of the fault, take corresponding measures to deal with it, repair the worn and loose parts and eliminate the fault phenomenon.
3、压力辊调整不当引起的质量故障
3. Quality failure caused by improper adjustment of pressure roller
如果压力辊太高或太，以致与瓦楞纸板接触过紧或过松，也会出现脏版、糊版或局部图文印迹不清晰，压辊应调整到适当的位置，使压辊与辊之间的间隙和板的合适厚度，确保印刷品生产零部件，避免故障现象。
If the pressure roller is too high or too low, so that the contact with the corrugated board is too tight or too loose, there will also be dirty plate, paste plate or unclear local graphic imprint. The pressure roller shall be adjusted to an appropriate position to make the gap between the pressure roller and the roller and the appropriate thickness of the plate, so as to ensure the production parts of printed matter and avoid failure.
4、印版厚薄不均造成的质量不合格。
4. Unqualified quality caused by uneven thickness of printing plate.
散板，经常能改遇到版面图文出现脏、这样它的厚度差异比较小。如果已经准备好橡胶板，存在厚度差，可以弥补局部在薄板背面胶层较多，使印版厚度基本保持一致，保证印刷压力和油墨均匀布局。
Scattered boards often encounter dirty graphics and text in the layout, so its thickness difference is relatively small. If the rubber plate has been prepared and there is a thickness difference, it can make up for the large number of adhesive layers on the back of the thin plate, so as to keep the thickness of the printing plate basically consistent and ensure the uniform layout of printing pressure and ink.
The wonderful contents of this article are provided by carton manufacturers. There are many wonderful contents on this website. You can click to enter more contents: https://www.shuangfengbaozhuang.cn We have special customer service to answer your questions
